Meter Maintenance

Electrode Cleaner 250ml

Flairform
9337839000958
Add to cart
Electrode Cleaner
Electrodes on meters invariably become coated with impurities, reducing their accuracy.
  • Suitable for both pH and conductivity meters
  • Removes both inorganic and organic contamination
  • Restores electrode accuracy and response time
  • Helps to maximise electrode life span

PH Electrode Storage Solution 250ml

Flairform
9337839001009
Add to cart
pH Meter and Pen Storage Solution
The most common cause of pH meter failure is dry storage of the electrode. This causes dehydration of both the glass electrode and wick.
  • helps maintain electrode accuracy and response time and eliminates reading 'drift'
  • maximises electrode life span by preventing dehydration of the glass electrode and wick

Note:  pH buffers 7.0 or 4.0 or distilled water are not suitable for storing pH electrodes. Electrode storage solutions are carefully structured formulations that do not interfere with the chemical composition of the liquid/gel that is contained within the electrode.

PH 7 250ml

Flairform
9337839000859
Add to cart
pH7 Calibration Solution
Flairform calibration solution is used to calibrate electronic test pens, to ensure accurate reading can be achieved.

All Flairform buffers are formulated with 'NIST' specified ingredients.

Stabilised to resist algae or growth formation.

PH 7 1 Litre

Flairform
9337839000873
Add to cart
pH7 Calibration Solution

PH 4 250ml

Flairform
9337839000903
Add to cart
ph4 Calibration Solution

PH 4 1 Litre

Flairform
9337839000927
Add to cart
ph4 Calibration Solution

EC 2.76 250ml

Flairform
9337839000804
Add to cart
EC2.76 Calibration Solution

EC 2.76 1 Litre

Flairform
9337839000828
Add to cart
ph4 Calibration Solution

EC Probe Cleaning Kit

Bluelab
9421024920579
Add to cart
Bluelab Cleaning Kit

Probe cleaning is one of the most important parts of owning and operating any Bluelab meter. If the probe is contaminated or dirty, it affects the accuracy of the reading displayed.

The probe surface is where the instrument takes the reading of the solution. The information is sent back from the probe to the electronic brain of the instrument.

A calculation is then done in the instruments brain or micro computer and a reading is then displayed. If the information sent back from the probe is inaccurate due to probe surface contamination then the reading will be inaccurate.

Cleaning the probes is a very easy task and prolongs the life of the probes.


The Bluelab EC Cleaning Kit contains;

  • Instructions
  • 2 x 20ml single use Conductivity standard solution sachets
  • Plastic Cup
  • Probe cleaner
  • Cleaning Tool


The Bluelab EC Cleaning Kit contains;

  • Instructions
  • 2 x 20ml single use Conductivity standard solution sachets
  • Plastic Cup
  • Probe cleaner
  • Cleaning Tool



 Suits
 Bluelab EC Truncheon
 Bluelab Combo Meter
 Bluelab Guardian Monitor
Instructions

Batteries (LR44) - Card of 10

Maxwell
4902580131401
Add to cart
LR44 Batteries


  • 1.5 volt
  • Alkaline Button Cell 
  • 10 batteries per card
  • Suits many hand held pH & EC meters 




WARNING - Keep button batteries out of reach of children.
Never allow children to replace button batteries in any device. If swallowed a button battery can cause severe or fatal injuries. If you think batteries may have been swallowed or placed inside any part of the body seek immediate medical attention. The Australian Poisons Information Centre can be contacted 24/7 on 13 11 26. Dispose of used button/coin batteries immediately.